Electro Industries SM1-16 Manual de usuario Pagina 22
- Pagina / 40
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
e
Electro Industries/GaugeTech
Doc #: E113-7-07 V1.04 2-2
AutoIP assigns a random valid address to the Ethernet Interface in the range of 169.254.x.1 to
169.254.x.1 where x can be between 0 and 255. This range of IP addresses is not to be used over the
Internet. If the Ethernet Interface has not been configured manually and cannot find a DHCP server,
it automatically chooses an address from the reserved range. The Ethernet Interface then uses the
Address Resolution Protocol (ARP) to send out a request asking if any node is using that address.
If another node is using the same address, the Ethernet Interface assigns another IP address, reboots
and repeats the sequence.
NOTE: AutoIP-enabled Ethernet Interfaces are constantly looking for DHCP servers. If a DHCP
server becomes available on the network, the AutoIP-enabled Ethernet Interface switches to the
DHCP server-provided address and the unit reboots. If the DHCP server exists but denies the
Ethernet Interface an IP address, the Ethernet Interface does not attach to the network, but waits and
retries.
• AutoIP allows a small network of AutoIP-enabled devices to be set up without any need for a
DHCP server or static IP addresses.
• AutoIP can be disabled by setting the IP address to 0.0.1.0. The 1 in the third octet is the
disabling factor.
2.6:
Setting
the
IP Address
Q
The Ethernet Interface's IP address must be configured before a network connection is available. If
the IP address was not set automatically via DHCP, set it now using a network and the setup
(configuration) menu.
Q
NETWORK PORT LOGIN
The ARP method is available under UNIX and Windows-based systems. The Ethernet Interface will
set its address from the first directed TCP/IP packet it receives.
Q
CLEARING THE ARP TABLE
Clearing an entry in the ARP table should be performed before and after setting the IP Address that
you will be using. In command prompt, type the following (insert your IP Address). Then press the
Enter key.
Q
ARP ON UNIX
On a Unix host, create an entry in the host's ARP table using the intended IP address and the
hardware address (or MAC Address) of the Ethernet Interface, which is found on the product label.
The label showing the MAC Address is found on the back panel (see section 1.2).
Q
ARP ON WINDOWS
In order for the ARP command to work on Windows, the RP table on the PC must have at least one
arp -d 191.12.3.77
arp -s 191.12.3.77 00:20:4a:xx:xx:xx
- SubstationMultiplexor 1
- Doc # E113-7-07 V1.04 3
- Table of Contents 7
- Doc # E113-7-07 V1.04 vi 8
- FFrroonntt 10
- VViieeww 10
- SSiiddee VViieeww 11
- BBaacckk 12
- PPaanneell 12
- Doc # E113-7-07 V1.04 1-6 14
- Shorted Internally 14
- Doc # E113-7-07 V1.04 1-7 15
- Substation Multiplexor 16
- Incorrect Connection: “T” 17
- Incorrect Connection: “Star” 17
- Doc # E113-7-07 V1.04 1-10 18
- Doc # E113-7-07 V1.04 1-11 19
- Doc # E113-7-07 V1.04 1-12 20
- Doc #: E113-7-07 V1.04 2-1 21
- Doc #: E113-7-07 V1.04 2-2 22
- Doc #: E113-7-07 V1.04 2-3 23
- Doc #: E113-7-07 V1.04 2-4 24
- Doc #: E113-7-07 V1.04 2-5 25
- Doc #: E113-7-07 V1.04 2-6 26
- Overview 27
- Doc # E113-7-07 V1.04 3-2 28
- Doc # E113-7-07 V1.04 3-3 29
- Doc # E113-7-07 V1.04 3-4 30
- Doc # E113-7-07 V1.04 3-5 31
- Doc # E113-7-07 V1.04 3-6 32
- Doc # E113-7-07 V1.04 3-7 33
- Doc # E113-7-07 V1.04 3-8 34
- Doc # E113-7-07 V1.04 3-9 35
- Doc # E113-7-07 V1.04 3-10 36
- 3.7: Port Status 37
- Doc # E113-7-07 V1.04 3-12 38
- Doc # E113-7-07 V1.04 3-13 39
- Doc # E113-7-07 V1.04 3-14 40
Whirlpool AWT 4093/1 manuály
Uživatelské manuály a uživatelské příručky pro Pračky Whirlpool AWT 4093/1.
Poskytujeme 3 manuály pdf Whirlpool AWT 4093/1 ke stažení zdarma podle typů dokumentů: Návod k použití
Comentarios a estos manuales