Electro Industries Shark 200T Especificaciones Pagina 207
- Pagina / 246
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
B: Modbus Map and Retrieving Logs
Doc# E149701 MM-19
Electro Industries/GaugeTech
The Leader In Power Monitoring and Smart Grid Solutions
Description (Note 1) Format Range (Note 6) Units or Resolution Comments # Reg
Modbus Address
Hex Decimal
Read-only
2B37 - 2B37 11064 - 11064 Current speed and format UINT16 bit-mapped
-abcde-- fghijklm
Bps: a=57600; b=38400; c=19200; d=14400; e=9600
Stop bits 'f': cleared 1 stop bit, set 2 stop bits
Parity: g=even; h=odd; i=none
Data bits: j=8; k=7; l=6; m=5
1
2B38 - 2B38 11065 - 11065 Reserved UINT16 bit-mapped Reserved 1
2B39 - 2B39 11066 - 11066 Current protocol UINT16 bit-mapped
-------- -----ppp-
ppp=protocol
100=DNP3; 010=Ascii Modbus; 001=Rtu Modbus
1
2B3A - 2B3A 11067 - 11067 Current reply delay UINT16 0 to 65535 milliseconds Delay to reply a Modbus transaction after receiving it. 1
2B3B - 2B3E 11068 - 11071 Reserved Reserved 4
Block Size: 8
read-only
2B3F - 2B78 11072 - 11129 Data and Control Block for Option Card 2
Meaning of registers depend on installed card. --
see below
Register assignments depend on which type of card is in
the slot. See overlays below.
58
Block Size: 66
read-only except as indicated
2B3F - 2B3F 11072 - 11072 Digital Input States UINT16 bit-mapped
-------- 22221111
Two nibble fields: (2222) for input#2 and (1111) for input
#1.
Lsb in each nibble is the current state of the input. Msb
in each nibble is the oldest registered state.
1
2B40 - 2B40 11073 - 11073 Digital Relay States UINT16 bit-mapped
-------- --ab--cd
If "a" is 1 then state of Relay#2 is unknown, otherwise
state of Relay#2 is in "c": (1=tripped, 0=released).
If "b" is 1 then state of Relay#1 is unknown, otherwise
state of Relay#1 is in "d": (1=tripped, 0=released).
1
2B41 - 2B41 11074 - 11074 Turn relay on UINT16 bit-mapped
-------- ------21
Writing a 1 in bit N turns relay N+1 ON (this register is
writeable only in privileged session)
1
2B42 - 2B42 11075 - 11075 Turn relay off UINT16 bit-mapp
ed
-------- ------21
Writing a 1 in bit N turns relay N+1 OFF (this register is
writeable only in privileged session)
1
2B43
-
2B43 11076 - 11076 Trip/Release delay timer for Relay 1 UINT16 0 to 9999 0.1 sec time to trip or release 1
2B44 - 2B44 11077 - 11077 Trip/Release delay timer for Relay 2 UINT16 0 to 9999 0.1 sec time to trip or release 1
2B45 - 2B46 11078 - 11079 Reserved Reserved 2
2B47 - 2B47 11080 - 11080 Input 1 Accumulator, Scaled UINT16 0 to 9999 1
2B48 - 2B48 11081 - 11081 Input 2 Accumulator, Scaled UINT16 0 to 9999 1
2B49 - 2B4A 11082 - 11083 Reserved Reserved 2
2B4B - 2B4B 11084 - 11084 Relay 1 Accumulator, Scaled UINT16 0 to 9999 1
2B4C - 2B4C 11085 - 11085 Relay 2 Accumulator, Scaled UINT16 0 to 9999 1
2B4D - 2B78 11086 - 11129 Reserved Reserved 44
Block Size: 58
resolution is 1, 10, 100, 1000,
10000, or 100000 counts
Disabled accumulators always read 0.
Data and Control Blocks for Option Card 2
Expansions for Data and Control Block for Option Card 2
Data and Control Block -- Digital I/O Relay Card Overlay (Note 15)
resolution is 1, 10, 100, 1000,
10000, or 100000 counts
Disabled accumulators always read 0.
Current Communication Settings for Option Card 2
- Shark 200 & 200T 1
- Statement of Calibration 6
- Disclaimer 6
- Table of Contents 9
- Industries/GaugeTech 10
- # E149701 1-1 13
- 1.1.1: Wye Connection 13
- # E149701 1-2 14
- # E149701 1-3 15
- # E149701 1-4 16
- 1.1.2: Delta Connection 16
- # E149701 1-5 17
- # E149701 1-6 18
- # E149701 1-7 19
- # E149701 1-8 20
- 1.2: Power, Energy and Demand 20
- # E149701 1-9 21
- # E149701 1-10 22
- # E149701 1-11 23
- # E149701 1-12 24
- # E149701 1-13 25
- # E149701 1-14 26
- 1.4: Harmonic Distortion 26
- # E149701 1-15 27
- # E149701 1-16 28
- # E149701 1-17 29
- 1.5: Power Quality 29
- # E149701 1-18 30
- 2.1.2: Ordering Information 34
- 2.1.4: Measured Values 38
- Table 1: 38
- 2.1.5: Utility Peak Demand 39
- 2.2: Specifications 40
- 2.3: Compliance 45
- 2.4: Accuracy 46
- Table 2: 46
- 3: Mechanical Installation 49
- 3.4: Transducer Installation 54
- 4: Electrical Installation 57
- $VSSFOUHJMMT 59
- OJDLFMQMBUFE 59
- CSBTTTUVET 59
- 5: Communication Installation 77
- UNICOM 2500 81
- Overview 82
- 6: Using the Shark® 200 Meter 97
- 6.2: Using the Front Panel 99
- Electro Industries/GaugeTech 100
- 6.2.6: Using Operating Mode 111
- 7: Using the I/O Option Cards 115
- 7.4: 1mA Output Card (1mAOS) 117
- 7.4.1: Specifications: 117
- 7.4.2: Default Configuration: 118
- 7.4.3: Wiring Diagram 119
- 7.5.1: Specifications 120
- 7.5.2: Default Configuration: 121
- 7.5.3: Wiring Diagram 122
- 7.6.1: Specifications 123
- 7.6.2: Wiring Diagram 125
- 7.7.1: Specifications 126
- 7.7.2: Default Configuration: 127
- 7.7.3: Wiring Diagram 128
- 7.8.1: Specifications 129
- 7.8.2: Wiring Diagram 130
- 7.9.1: Specifications 131
- 7.9.2: Default Configuration 132
- 7.9.3: Wiring Diagram 132
- 8.1: Overview 133
- 8.2: Hardware Connection 133
- 8.4: Ethernet Card Features 134
- 8.4.1: Ethernet Communication 134
- 8.4.2: Embedded Web Server 134
- 9: Data Logging 141
- A.1: Introduction 143
- B.1: Introduction 149
- B.3: Data Formats 149
- B.4: Floating Point Values 150
- B.5.1: Data Formats 152
- B.5.2: Shark® 200 Meter Logs 152
- B.5.3: Block Definitions 154
- B.5.4: Log Retrieval 164
- B.5.4.1: Auto-Increment 164
- B.5.6: Examples 184
- B.6.1: Hex Representation 187
- B.6.2: Decimal Representation 187
- C: DNP Mapping 229
- C.4: Application Layer 230
- C.5: Error Reply 231
- C.6: Shark 231
- 200 Meter’s DNP Register Map 231
- C.7: DNP Message Layouts 234
- C.8: Internal Indication Bits 237
- D.1: Introduction 239
- D.2: Installation Procedures 239
Relacionado con productos y manuales para Multímetros Electro Industries Shark 200T
(8 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.068 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales