Electro Industries Shark 200T Especificaciones Pagina 218
- Pagina / 246
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
B: Modbus Map and Retrieving Logs
Doc# E149701 MM-30
Electro Industries/GaugeTech
The Leader In Power Monitoring and Smart Grid Solutions
Description (Note 1) Format Range (Note 6) Units or Resolution Comments # Reg
Modbus Address
Hex Decimal
7E07 - 7E0E 32264 - 32271 Input#2 Accumulator Label ASCII 16 char 8
7E0F - 7E16 32272 - 32279 Input#3 Accumulator Label ASCII 16 char 8
7E17 - 7E1E 32280 - 32287 Input#4 Accumulator Label ASCII 16 char 8
7E1F - 7E1F 32288 - 32288 Input#1 Accumulator Kt UINT16 bit-mapped
ddVVVVVV VVVVVVVV
1
7E20 - 7E20 32289 - 32289 Input#2 Accumulator Kt UINT16 bit-mapped
ddVVVVVV VVVVVVVV
1
7E21 - 7E21 32290 - 32290 Input#3 Accumulator Kt UINT16 bit-mapped
ddVVVVVV VVVVVVVV
1
7E22 - 7E22 32291 - 32291 Input#4 Accumulator Kt UINT16 bit-mapped
ddVVVVVV VVVVVVVV
1
7E23 - 7F3E 32292 - 32575 Reserved Reserved 284
Block Size: 512
Second Overlay write only in PS update mode
7D3F - 7D3F 32064 - 32064 Update rate UINT16 0 to 65535 milliseconds Fixed -- see specifications. 1
7D40 - 7D40 32065 - 32065 Channel direction - 1mA Card only! UINT16 bit-mapped
-------- ----4321
Full range output for 0-1mA card only: A bit set(1) means
full range (-1mA to +1mA); a bit cleared(0) means source
only (0mA to +1mA).
1
7D41 - 7D41 32066 - 32066 Format parameter for output #1 UINT16 bit-mapped
-------- ---f suwb
Format of the polled register:f=float 32; s=signed 32 bit
int; u=unsigned 32 bit int; w=signed 16 bit int;
b=unsigned 16 bit int.
1
7D42 - 7D42 32067 - 32067 Source register for Output#1 UINT16 0 to 65535 This register should be programmed with the address of
the register whose value is to be used for current output.
In different words, the current level output of analog
board will follow the value of the register addressed here.
1
7D43 - 7D44 32068 - 32069 High value of source register for output#1 Value read from the source register at which High
nominal current will be output. Example: for the 4-20mA
card, if this register is programmed with 750, then the
current output will be 20mA when the value read from the
source register is 750.
2
7D45 - 7D46 32070 - 32071 Low value of source register for output#1 Value read from the source register at which Low
nominal current will be output. Example: for the 4-20mA
card, if this register is programmed with 0, then the
current output will be 4mA when the value read from the
source register is 0.
2
7D47
-
7D4C 32072 - 32077 Analog output#2 format, register, max & min 6
7D4D - 7D52 32078 - 32083 Analog output#3 format, register, max & min 6
7D53 - 7D58 32084 - 32089 Analog output#4 format, register, max & min 6
7D59 - 7F3E 32090 - 32575 Reserved Reserved 486
Block Size: 512
Same as analog output#1
Same as analog output#1
Same as analog output#1
KT power factor for the accumulator input
"V" is raw power value in Wh/pulse from 0 to 9999.
"dd"=decimal point position: 00=0.XXXX, 01=X.XXX,
10=XX.XX, 11= X.XXX.
Settings Registers for Analog Out 0-1mA / Analog Out 4-20mA Cards
Depends on the format parameter
Depends on the format parameter
- Shark 200 & 200T 1
- Statement of Calibration 6
- Disclaimer 6
- Table of Contents 9
- Industries/GaugeTech 10
- # E149701 1-1 13
- 1.1.1: Wye Connection 13
- # E149701 1-2 14
- # E149701 1-3 15
- # E149701 1-4 16
- 1.1.2: Delta Connection 16
- # E149701 1-5 17
- # E149701 1-6 18
- # E149701 1-7 19
- # E149701 1-8 20
- 1.2: Power, Energy and Demand 20
- # E149701 1-9 21
- # E149701 1-10 22
- # E149701 1-11 23
- # E149701 1-12 24
- # E149701 1-13 25
- # E149701 1-14 26
- 1.4: Harmonic Distortion 26
- # E149701 1-15 27
- # E149701 1-16 28
- # E149701 1-17 29
- 1.5: Power Quality 29
- # E149701 1-18 30
- 2.1.2: Ordering Information 34
- 2.1.4: Measured Values 38
- Table 1: 38
- 2.1.5: Utility Peak Demand 39
- 2.2: Specifications 40
- 2.3: Compliance 45
- 2.4: Accuracy 46
- Table 2: 46
- 3: Mechanical Installation 49
- 3.4: Transducer Installation 54
- 4: Electrical Installation 57
- $VSSFOUHJMMT 59
- OJDLFMQMBUFE 59
- CSBTTTUVET 59
- 5: Communication Installation 77
- UNICOM 2500 81
- Overview 82
- 6: Using the Shark® 200 Meter 97
- 6.2: Using the Front Panel 99
- Electro Industries/GaugeTech 100
- 6.2.6: Using Operating Mode 111
- 7: Using the I/O Option Cards 115
- 7.4: 1mA Output Card (1mAOS) 117
- 7.4.1: Specifications: 117
- 7.4.2: Default Configuration: 118
- 7.4.3: Wiring Diagram 119
- 7.5.1: Specifications 120
- 7.5.2: Default Configuration: 121
- 7.5.3: Wiring Diagram 122
- 7.6.1: Specifications 123
- 7.6.2: Wiring Diagram 125
- 7.7.1: Specifications 126
- 7.7.2: Default Configuration: 127
- 7.7.3: Wiring Diagram 128
- 7.8.1: Specifications 129
- 7.8.2: Wiring Diagram 130
- 7.9.1: Specifications 131
- 7.9.2: Default Configuration 132
- 7.9.3: Wiring Diagram 132
- 8.1: Overview 133
- 8.2: Hardware Connection 133
- 8.4: Ethernet Card Features 134
- 8.4.1: Ethernet Communication 134
- 8.4.2: Embedded Web Server 134
- 9: Data Logging 141
- A.1: Introduction 143
- B.1: Introduction 149
- B.3: Data Formats 149
- B.4: Floating Point Values 150
- B.5.1: Data Formats 152
- B.5.2: Shark® 200 Meter Logs 152
- B.5.3: Block Definitions 154
- B.5.4: Log Retrieval 164
- B.5.4.1: Auto-Increment 164
- B.5.6: Examples 184
- B.6.1: Hex Representation 187
- B.6.2: Decimal Representation 187
- C: DNP Mapping 229
- C.4: Application Layer 230
- C.5: Error Reply 231
- C.6: Shark 231
- 200 Meter’s DNP Register Map 231
- C.7: DNP Message Layouts 234
- C.8: Internal Indication Bits 237
- D.1: Introduction 239
- D.2: Installation Procedures 239
Relacionado con productos y manuales para Multímetros Electro Industries Shark 200T
(8 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.038 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales