Electro Industries Shark 200T Especificaciones Pagina 210
- Pagina / 246
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
B: Modbus Map and Retrieving Logs
Doc# E149701 MM-22
Electro Industries/GaugeTech
The Leader In Power Monitoring and Smart Grid Solutions
Description (Note 1) Format Range (Note 6) Units or Resolution Comments # Reg
Modbus Address
Hex Decimal
4E28 - 4E28 20009 - 20009 Reset Waveform Capture Log UINT16 password (Note 5) 1
4E29 - 4E2A 20010 - 20011 Reserved Reserved 2
4E2B - 4E2B 20012 - 20012 Reset Option Card 1 Input Accumulators UINT16 password (Note 5) 1
4E2C - 4E2C 20013 - 20013 Reset Option Card 1 Output Accumulators UINT16 password (Note 5) 1
4E2D - 4E2D 20014 - 20014 Reset Option Card 2 Input Accumulators UINT16 password (Note 5) 1
4E2E - 4E2E 20015 - 20015 Reset Option Card 2 Output Accumulators UINT16 password (Note 5) 1
Block Size: 16
conditional write
5207 - 5207 21000 - 21000 Initiate Meter Firmware Reprogramming UINT16 password (Note 5) 1
5208 - 5208 21001 - 21001 Force Meter Restart UINT16 password (Note 5) causes a watchdog reset, always reads 0 1
5209 - 5209 21002 - 21002 Open Privileged Command Session UINT16 password (Note 5) meter will process command registers (this register
through 'Close Privileged Command Session' register
below) for 5 minutes or until the session is closed,
whichever comes first.
1
520A - 520A 21003 - 21003 Initiate Programmable Settings Update UINT16 password (Note 5) meter enters PS update mode 1
520B - 520B 21004 - 21004 Calculate Programmable Settings Checksum
(Note 3)
UINT16 0000 to 9999 meter calculates checksum on RAM copy of PS block 1
520C - 520C 21005 - 21005 Programmable Settings Checksum (Note 3) UINT16 0000 to 9999 read/write checksum register; PS block saved in
nonvolatile memory on write (Note 8)
1
520D - 520D 21006 - 21006 Write New Password (Note 3) UINT16 0000 to 9999 write-only register; always reads zero 1
520E - 520E 21007 - 21007 Terminate Programmable Settings Update (Note
3)
UINT16 any value meter leaves PS update mode via reset 1
520F - 5211 21008 - 21010 Set Meter Clock TSTAMP 1Jan2000 - 31Dec2099 1 sec saved only when 3rd register is written 3
5212 - 5212 21011 - 21011 Manually Trigger Waveform Capture UINT16 any value applies to Shark 300 only; returns busy exception if
blocked by another capture in progress
1
5213 - 5219 21012 - 21018 Reserved Reserved 7
521A - 521A 21019 - 21019 Close Privileged Command Session UINT16 any value ends an o
pen command session 1
Block Size:
20
read/write
658F - 659A 26000 - 26011 Perform a Secure Operation UINT16 encrypted command to read password or change meter
type
12
Block Size: 12
Encryption Block
Privileged Commands Block
- Shark 200 & 200T 1
- Statement of Calibration 6
- Disclaimer 6
- Table of Contents 9
- Industries/GaugeTech 10
- # E149701 1-1 13
- 1.1.1: Wye Connection 13
- # E149701 1-2 14
- # E149701 1-3 15
- # E149701 1-4 16
- 1.1.2: Delta Connection 16
- # E149701 1-5 17
- # E149701 1-6 18
- # E149701 1-7 19
- # E149701 1-8 20
- 1.2: Power, Energy and Demand 20
- # E149701 1-9 21
- # E149701 1-10 22
- # E149701 1-11 23
- # E149701 1-12 24
- # E149701 1-13 25
- # E149701 1-14 26
- 1.4: Harmonic Distortion 26
- # E149701 1-15 27
- # E149701 1-16 28
- # E149701 1-17 29
- 1.5: Power Quality 29
- # E149701 1-18 30
- 2.1.2: Ordering Information 34
- 2.1.4: Measured Values 38
- Table 1: 38
- 2.1.5: Utility Peak Demand 39
- 2.2: Specifications 40
- 2.3: Compliance 45
- 2.4: Accuracy 46
- Table 2: 46
- 3: Mechanical Installation 49
- 3.4: Transducer Installation 54
- 4: Electrical Installation 57
- $VSSFOUHJMMT 59
- OJDLFMQMBUFE 59
- CSBTTTUVET 59
- 5: Communication Installation 77
- UNICOM 2500 81
- Overview 82
- 6: Using the Shark® 200 Meter 97
- 6.2: Using the Front Panel 99
- Electro Industries/GaugeTech 100
- 6.2.6: Using Operating Mode 111
- 7: Using the I/O Option Cards 115
- 7.4: 1mA Output Card (1mAOS) 117
- 7.4.1: Specifications: 117
- 7.4.2: Default Configuration: 118
- 7.4.3: Wiring Diagram 119
- 7.5.1: Specifications 120
- 7.5.2: Default Configuration: 121
- 7.5.3: Wiring Diagram 122
- 7.6.1: Specifications 123
- 7.6.2: Wiring Diagram 125
- 7.7.1: Specifications 126
- 7.7.2: Default Configuration: 127
- 7.7.3: Wiring Diagram 128
- 7.8.1: Specifications 129
- 7.8.2: Wiring Diagram 130
- 7.9.1: Specifications 131
- 7.9.2: Default Configuration 132
- 7.9.3: Wiring Diagram 132
- 8.1: Overview 133
- 8.2: Hardware Connection 133
- 8.4: Ethernet Card Features 134
- 8.4.1: Ethernet Communication 134
- 8.4.2: Embedded Web Server 134
- 9: Data Logging 141
- A.1: Introduction 143
- B.1: Introduction 149
- B.3: Data Formats 149
- B.4: Floating Point Values 150
- B.5.1: Data Formats 152
- B.5.2: Shark® 200 Meter Logs 152
- B.5.3: Block Definitions 154
- B.5.4: Log Retrieval 164
- B.5.4.1: Auto-Increment 164
- B.5.6: Examples 184
- B.6.1: Hex Representation 187
- B.6.2: Decimal Representation 187
- C: DNP Mapping 229
- C.4: Application Layer 230
- C.5: Error Reply 231
- C.6: Shark 231
- 200 Meter’s DNP Register Map 231
- C.7: DNP Message Layouts 234
- C.8: Internal Indication Bits 237
- D.1: Introduction 239
- D.2: Installation Procedures 239
Relacionado con productos y manuales para Multímetros Electro Industries Shark 200T
(8 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.071 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales