Electro Industries Shark 200T Especificaciones Pagina 144
- Pagina / 298
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Doc# E149701 8 - 2
8: Using the INP100S Network Card
Electro Industries/GaugeTech
The Leader In Power Monitoring and Smart Grid Solutions
Electro Industries/GaugeTech
The Leader In Power Monitoring and Smart Grid Solutions
8.3: Performing Network Configuration
As with the other Option cards, the Shark® 200 meter auto-detects the presence of
an installed Ethernet card. Configure the Ethernet card through Communicator EXT
TM
software. Refer to Chapter 5 of the Communicator EXT
TM
User Manual for instructions.
You can open the manual online by clicking Help>Contents from the Communicator
EXT
TM
Main screen.
8.4: INP100S Ethernet Card Features
The INP100S Ethernet card gives your meter the following capabilities:
• Ethernet communication
• Embedded Web server
• NTP Time Server synchronization
8.4.1: Ethernet Communication
The INP100S enables high-speed Ethernet communication with up to 12 simultaneous
connections for Modbus TCP. The card supports a static IP address and is treated like
a node on the network.
8.4.2: Embedded Web Server
The INP100S gives the meter a Web server that is viewable over the Ethernet by
almost all browsers. The Shark® Series webpages allow you to see the following
information for the Shark® 200 meter:
• Voltage and current readings
• Power and Energy readings
• Power quality information
• General meter information
You can also upgrade the Ethernet (Network) card’s firmware and/or Reset the Net-
work card from the Meter Information web page.
The INP100S card also supports the “keep alive” feature - see Section 8.4.5.
- Shark 200 & 200T 1
- Use Of Product for Protection 6
- Statement of Calibration 6
- Disclaimer 6
- Table of Contents 9
- Industries/GaugeTech 10
- 1.1.1: Wye Connection 13
- 1.1.2: Delta Connection 16
- 1.2: Power, Energy and Demand 20
- 1.4: Harmonic Distortion 26
- 1.5: Power Quality 29
- 2.1.2: Ordering Information 34
- 2.1.3: V-Switch 36
- Key Technology 36
- 2.1.4: Measured Values 38
- Table 1: 38
- 2.1.5: Utility Peak Demand 39
- 2.2: Specifications 40
- 2.3: Compliance 45
- 2.4: Accuracy 46
- Table 2: 46
- 3: Mechanical Installation 49
- 3.4: Transducer Installation 54
- 4: Electrical Installation 57
- $VSSFOUHJMMT 60
- OJDLFMQMBUFE 60
- CSBTTTUVET 60
- 5.1.1: IrDA Port (Com 1) 79
- Electro Industries/GaugeTech 80
- UNICOM 2500 83
- Overview 84
- Software 85
- 6: Using the Shark® 200 Meter 103
- 6.2: Using the Front Panel 105
- 6.2.6: Using Operating Mode 117
- 7: Using the I/O Option Cards 121
- 7.2: Installing Option Cards 122
- 7.4: 1mA Output Card (1mAOS) 124
- 7.4.1: Specifications: 124
- 7.4.2: Default Configuration: 125
- 7.4.3: Wiring Diagram 126
- 7.5.1: Specifications 127
- 7.5.2: Default Configuration: 128
- 7.5.3: Wiring Diagram 129
- 7.6.1: Specifications 130
- 7.6.2: Wiring Diagram 132
- 7.7.1: Specifications 133
- 7.7.2: Default Configuration: 134
- 7.7.3: Wiring Diagram 135
- 7.8.1: Specifications 136
- 7.8.2: Wiring Diagram 137
- 7.9.1: Specifications 138
- 7.9.2: Default Configuration 139
- 7.9.3: Wiring Diagram 139
- 7.10.1: Specifications 140
- 7.10.2: Default Configuration 141
- 7.10.3: Wiring Diagram 141
- 8.1: Overview 143
- 8.2: Hardware Connection 143
- 8.4.1: Ethernet Communication 144
- 8.4.2: Embedded Web Server 144
- 8.4.5: Keep-Alive Feature 151
- 9: Data Logging 153
- A.1: Introduction 155
- B.1: Introduction 161
- B.3: Data Formats 161
- B.4: Floating Point Values 162
- Byte 012345678910111213 164
- B.5.3: Block Definitions 166
- B.5.4: Log Retrieval 176
- B.5.4.1: Auto-Increment 176
- B.5.6: Examples 196
- B.6.1: Hex Representation 199
- B.6.2: Decimal Representation 199
- C: DNP Mapping 243
- C.3: Data Link Layer 244
- C.4: Application Layer 244
- C.5: Error Reply 246
- C.6: Object Specifics 246
- C.7: DNP Object Point Map 248
- C.8: DNP Message Layouts 257
- C.9: Internal Indication Bits 260
- D.1: Introduction 261
- D.2: Installation Procedures 261
- Network Card (INP300S) 269
- E.1.5: Reference Materials 280
- Network Card 281
- E.2.1: Overview 281
- System Log 293
- Firmware 294
- E.6: Keep-Alive Feature 296
- E.7: Testing 296
- E.8: Error Codes 297
Relacionado con productos y manuales para Multímetros Electro Industries Shark 200T
(246 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.079 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales