Electro Industries Shark 200T Especificaciones descargar pdf (Pagina 228)

B: Modbus Map and Retrieving Logs

Doc# E149701 MM-28

Electro Industries/GaugeTech

The Leader In Power Monitoring and Smart Grid Solutions

Description (Note 1) Format Range (Note 6) Units or Resolution Comments # Reg

Modbus Address

Hex Decimal

7D21 - 7D21 32034 - 32034 Input Accumulators Scaling UINT16 bit-mapped

-------- 22221111

7D22 - 7D22 32035 - 32035 Relay Accumulators Scaling UINT16 bit-mapped

-------- 22221111

7D23 - 7D23 33036 - 33036 Fast pulse input selector UINT16 bit-mapped

p------- -----nnn

When value 'nnn' is non-zero, it determines which of the

card inputs will be a fast pulse detection input.

The polarity bit 'P' tells the event to be detected: 1=open-

to-close; 0=close-to-open. There is no “any-change”

detection mode.

7D24 - 7D3E 32037 - 32063 Reserved Set to 0. 27

Block Size: 63

First Overlay write only in PS update mode

7D00 - 7D00 32001 - 32001 Input#1 - 4 bindings & logging enables UINT16 bit-mapped

44443333 22221111

One nibble for each input.

Assuming "abcc" as the bits in each nibble:

"a": select this input for EOI (End Of Interval)pulse

sensing.

"b": log this input when pulse is detected

"cc": Input event trigger mode - Contact sensing method;

00 = none; 01 = open to close; 10 = close to open; 11 =

any change.

Every input has an associated internal accumulator (See

input Accumulator Scaling), which is incremented every

time the input changes according with the trigger mode

crieteria “cc”

7D01 - 7D01 32002 - 32002 Source for Pulse Ouput#1 UINT16 enumeration

-----ppp ----vvvv

" ppp" (Phase) : 000 = none, 001 = Phase A, 010 =

Phase B, 011 = Phase C, 100 = All Phases, 101 = Pulse

from EOI(End Of Interval).

"vvvv"(Value) :

0000= none,

0001 = Wh,

0010 = +Wh,

0011 = -Wh,

0100= Varh,

0101 = +Varh,

0110 = -Varh,

0111 = VAh,

1000= Received Wh,

1001= Delivered Wh,

1010= Inductive Varh,

1011 = Capacitive Varh

7D02 - 7D02 32003 - 32003 Kt [Wh/pulse] factor for Pulse Output#1 UINT16 bit-mapped

ddVVVVVV VVVVVVVV

"V…V" = not scaled energy value per pulse, from 0 to

9999.

"dd"= decimal point position: 00=0.XXXX, 01=X.XXX,

10=XX.XX, 11= X.XXX.

7D03 - 7D04 32004 - 32005 Output#2 Assignment and Kt UINT16 2

7D05 - 7D06 32006 - 32007 Output#3 Assignment and Kt UINT16 2

Settings Registers for Digital I/O Pulse Output Card

same as Output #1

4 bits per input or output accumulator

The nibble informs what should be the scaling of the

accumulator 0=no-scaling, 1=0.1, 2=0.01, 3= 1m,

4=0.1m, 5=0.01m, 6=1u, 7=0.1u; the value 15 disable

the accumulator.

Example: suppose that the internal input accumulator #1

is 12345, and its corresponding scaling setting is “0011”

(3 decimal). Then, the accumulator will be read as:

Scaling 3, means 1m or 0.001.

Scaled accumulator = 12345 * 0.001 = 12 (Twelve).

1 2 ... 223 224 225 226 227 228 229 230 231 232 233 ... 297 298

Comentarios a estos manuales

Sin comentarios

Electro Industries Shark 200T Especificaciones Pagina 228

Comentarios a estos manuales

Relacionado con productos y manuales para Multímetros Electro Industries Shark 200T