Electro Industries Shark 200T Especificaciones Pagina 233
- Pagina / 298
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
B: Modbus Map and Retrieving Logs
Doc# E149701 MM-33
Electro Industries/GaugeTech
The Leader In Power Monitoring and Smart Grid Solutions
Description (Note 1) Format Range (Note 6) Units or Resolution Comments # Reg
Modbus Address
Hex Decimal
First Overlay write only in PS update mode
80E8 - 80E8 33001 - 33001 Input#1 - 4 bindings & logging enables UINT16 bit-mapped
44443333 22221111
One nibble for each input.
Assuming "abcc" as the bits in each nibble:
"a": select this input for EOI (End Of Interval)pulse
sensing.
"b": log this input when pulse is detected
"cc": Input event trigger mode - Contact sensing method;
00 = none; 01 = open to close; 10 = close to open; 11 =
any change.
Every input has an associated internal accumulator (See
input Accumulator Scaling), which is incremented every
time the input changes according with the trigger mode
crieteria “cc”
1
80E9 - 80E9 33002 - 33002 Source for Pulse Ouput#1 UINT16 enumeration
-----ppp ----vvvv
" ppp" (Phase) : 000 = none, 001 = Phase A, 010 =
Phase B, 011 = Phase C, 100 = All Phases, 101 = Pulse
from EOI(End Of Interval).
"vvvv"(Value) :
0000= none,
0001 = Wh,
0010 = +Wh,
0011 = -Wh,
0100= Varh,
0101 = +Varh,
0110 = -Varh,
0111 = VAh,
1000= Received Wh,
1001= Delivered Wh,
1010= Inductive Varh,
1011 = Capacitive Varh
1
80EA - 80EA 33003 - 33003 Kt [Wh/pulse] factor for Pulse Output#1 UINT16 bit-mapped
ddVVVVVV VVVVVVVV
"V…V" = not scaled energy value per pulse, from 0 to
9999.
"dd"= decimal point position: 00=0.XXXX, 01=X.XXX,
10=XX.XX, 11= X.XXX.
1
80EB - 80EC 33004 - 33005 Output#2 Assignment and Kt UINT16 2
80ED - 80EE 33006 - 33007 Output#3 Assignment and Kt UINT16 2
80EF - 80F0 33008 - 33009 Output#4 Assignment and Kt UINT16 2
80F1 - 80F1 33010 - 33010 Input Accumulators Scaling UINT16 bit-mapped
44443333 22221111
1
80F2 - 80F2 33011 - 33011 Output Accumulators Scaling UINT16 bit-mapped
44443333 22221111
1
80F3 - 80F3 33012 - 33012 Fast pulse input selector UINT16 bit-mapped
p------- -----nnn
When value 'nnn' is non-zero, it determines which of the
card inputs will be a fast pulse detection input.
The polarity bit 'P' tells the event to be detected: 1=open-
to-close; 0=close-to-open. There is no “any-change”
detection mode.
1
80F4 - 8126 33013 - 33063 Reserved Reserved 51
Block Size: 63
Settings Registers for Digital I/O Pulse Output Card
same as Output #1
same as Output #1
same as Output #1
see Relay Card above
- Shark 200 & 200T 1
- Use Of Product for Protection 6
- Statement of Calibration 6
- Disclaimer 6
- Table of Contents 9
- Industries/GaugeTech 10
- 1.1.1: Wye Connection 13
- 1.1.2: Delta Connection 16
- 1.2: Power, Energy and Demand 20
- 1.4: Harmonic Distortion 26
- 1.5: Power Quality 29
- 2.1.2: Ordering Information 34
- 2.1.3: V-Switch 36
- Key Technology 36
- 2.1.4: Measured Values 38
- Table 1: 38
- 2.1.5: Utility Peak Demand 39
- 2.2: Specifications 40
- 2.3: Compliance 45
- 2.4: Accuracy 46
- Table 2: 46
- 3: Mechanical Installation 49
- 3.4: Transducer Installation 54
- 4: Electrical Installation 57
- $VSSFOUHJMMT 60
- OJDLFMQMBUFE 60
- CSBTTTUVET 60
- 5.1.1: IrDA Port (Com 1) 79
- Electro Industries/GaugeTech 80
- UNICOM 2500 83
- Overview 84
- Software 85
- 6: Using the Shark® 200 Meter 103
- 6.2: Using the Front Panel 105
- 6.2.6: Using Operating Mode 117
- 7: Using the I/O Option Cards 121
- 7.2: Installing Option Cards 122
- 7.4: 1mA Output Card (1mAOS) 124
- 7.4.1: Specifications: 124
- 7.4.2: Default Configuration: 125
- 7.4.3: Wiring Diagram 126
- 7.5.1: Specifications 127
- 7.5.2: Default Configuration: 128
- 7.5.3: Wiring Diagram 129
- 7.6.1: Specifications 130
- 7.6.2: Wiring Diagram 132
- 7.7.1: Specifications 133
- 7.7.2: Default Configuration: 134
- 7.7.3: Wiring Diagram 135
- 7.8.1: Specifications 136
- 7.8.2: Wiring Diagram 137
- 7.9.1: Specifications 138
- 7.9.2: Default Configuration 139
- 7.9.3: Wiring Diagram 139
- 7.10.1: Specifications 140
- 7.10.2: Default Configuration 141
- 7.10.3: Wiring Diagram 141
- 8.1: Overview 143
- 8.2: Hardware Connection 143
- 8.4.1: Ethernet Communication 144
- 8.4.2: Embedded Web Server 144
- 8.4.5: Keep-Alive Feature 151
- 9: Data Logging 153
- A.1: Introduction 155
- B.1: Introduction 161
- B.3: Data Formats 161
- B.4: Floating Point Values 162
- Byte 012345678910111213 164
- B.5.3: Block Definitions 166
- B.5.4: Log Retrieval 176
- B.5.4.1: Auto-Increment 176
- B.5.6: Examples 196
- B.6.1: Hex Representation 199
- B.6.2: Decimal Representation 199
- C: DNP Mapping 243
- C.3: Data Link Layer 244
- C.4: Application Layer 244
- C.5: Error Reply 246
- C.6: Object Specifics 246
- C.7: DNP Object Point Map 248
- C.8: DNP Message Layouts 257
- C.9: Internal Indication Bits 260
- D.1: Introduction 261
- D.2: Installation Procedures 261
- Network Card (INP300S) 269
- E.1.5: Reference Materials 280
- Network Card 281
- E.2.1: Overview 281
- System Log 293
- Firmware 294
- E.6: Keep-Alive Feature 296
- E.7: Testing 296
- E.8: Error Codes 297
Relacionado con productos y manuales para Multímetros Electro Industries Shark 200T
(246 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.053 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales