Electro Industries Shark 200T Especificaciones Pagina 239
- Pagina / 298
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
B: Modbus Map and Retrieving Logs
Doc# E149701 MM-39
Electro Industries/GaugeTech
The Leader In Power Monitoring and Smart Grid Solutions
Description (Note 1) Format Range (Note 6) Units or Resolution Comments # Reg
Modbus Address
Hex Decimal
C787 - C796 51080 - 51095
I/O Change Log Status Block
16
C797 - C7A6 51096 - 51111
Power Quality Log Status Block
16
C7A7 - C7B6 51112 - 51127
Waveform Capture Log Status Block
16
Block Size: 128
FLOAT 32-bit IEEE floating point number spanning 2 registers. The lower-addressed register is the high order half (i.e., contains the exponent).
TSTAMP 3 adjacent registers, 2 bytes each. First (lowest-addressed) register high byte is year (0-99), low byte is month (1-12). Middle register high byte is day(1-31), low byte is hour (0-23 plus DST bit).
DST (daylight saving time) bit is bit 6 (0x40). Third register high byte is minutes (0-59), low byte is seconds (0-59). For example, 9:35:07AM on October 12, 2049 would be 0x310A, 0x0C49, 0x2307,
assuming DST is in effect.
Data Formats
ASCII ASCII characters packed 2 per register in high, low order and without any termination characters. For example, "Shark200" would be 4 registers containing 0x5378, 0x6172, 0x6B32, 0x3030.
SINT16 / UINT16 16-bit signed / unsigned integer.
SINT32 / UINT32 32-bit signed / unsigned integer spanning 2 registers. The lower-addressed register is the high order half.
same as alarm log status block
same as alarm log status block
same as alarm log status block
End of Map
- Shark 200 & 200T 1
- Use Of Product for Protection 6
- Statement of Calibration 6
- Disclaimer 6
- Table of Contents 9
- Industries/GaugeTech 10
- 1.1.1: Wye Connection 13
- 1.1.2: Delta Connection 16
- 1.2: Power, Energy and Demand 20
- 1.4: Harmonic Distortion 26
- 1.5: Power Quality 29
- 2.1.2: Ordering Information 34
- 2.1.3: V-Switch 36
- Key Technology 36
- 2.1.4: Measured Values 38
- Table 1: 38
- 2.1.5: Utility Peak Demand 39
- 2.2: Specifications 40
- 2.3: Compliance 45
- 2.4: Accuracy 46
- Table 2: 46
- 3: Mechanical Installation 49
- 3.4: Transducer Installation 54
- 4: Electrical Installation 57
- $VSSFOUHJMMT 60
- OJDLFMQMBUFE 60
- CSBTTTUVET 60
- 5.1.1: IrDA Port (Com 1) 79
- Electro Industries/GaugeTech 80
- UNICOM 2500 83
- Overview 84
- Software 85
- 6: Using the Shark® 200 Meter 103
- 6.2: Using the Front Panel 105
- 6.2.6: Using Operating Mode 117
- 7: Using the I/O Option Cards 121
- 7.2: Installing Option Cards 122
- 7.4: 1mA Output Card (1mAOS) 124
- 7.4.1: Specifications: 124
- 7.4.2: Default Configuration: 125
- 7.4.3: Wiring Diagram 126
- 7.5.1: Specifications 127
- 7.5.2: Default Configuration: 128
- 7.5.3: Wiring Diagram 129
- 7.6.1: Specifications 130
- 7.6.2: Wiring Diagram 132
- 7.7.1: Specifications 133
- 7.7.2: Default Configuration: 134
- 7.7.3: Wiring Diagram 135
- 7.8.1: Specifications 136
- 7.8.2: Wiring Diagram 137
- 7.9.1: Specifications 138
- 7.9.2: Default Configuration 139
- 7.9.3: Wiring Diagram 139
- 7.10.1: Specifications 140
- 7.10.2: Default Configuration 141
- 7.10.3: Wiring Diagram 141
- 8.1: Overview 143
- 8.2: Hardware Connection 143
- 8.4.1: Ethernet Communication 144
- 8.4.2: Embedded Web Server 144
- 8.4.5: Keep-Alive Feature 151
- 9: Data Logging 153
- A.1: Introduction 155
- B.1: Introduction 161
- B.3: Data Formats 161
- B.4: Floating Point Values 162
- Byte 012345678910111213 164
- B.5.3: Block Definitions 166
- B.5.4: Log Retrieval 176
- B.5.4.1: Auto-Increment 176
- B.5.6: Examples 196
- B.6.1: Hex Representation 199
- B.6.2: Decimal Representation 199
- C: DNP Mapping 243
- C.3: Data Link Layer 244
- C.4: Application Layer 244
- C.5: Error Reply 246
- C.6: Object Specifics 246
- C.7: DNP Object Point Map 248
- C.8: DNP Message Layouts 257
- C.9: Internal Indication Bits 260
- D.1: Introduction 261
- D.2: Installation Procedures 261
- Network Card (INP300S) 269
- E.1.5: Reference Materials 280
- Network Card 281
- E.2.1: Overview 281
- System Log 293
- Firmware 294
- E.6: Keep-Alive Feature 296
- E.7: Testing 296
- E.8: Error Codes 297
Relacionado con productos y manuales para Multímetros Electro Industries Shark 200T
(246 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.075 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales